CCNA - IOS DUMPS

-
Question 1


 Which command encrypts all plaintext passwords?

 A. Router# service password-encryption
B. Router(config)# password-encryption
C. Router(config)# service password-encryption
D. Router# password-encryption


 Answer: C


 Question 2


 What can be done to secure the virtual terminal interfaces on a router? (Choose two)

 A. Administratively shut down the interface.
B. Physically secure the interface.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group
command.
D. Configure a virtual terminal password and login process.
E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.


 Answer: D E


 Question 3

 Refer to the exhibit. Why is flash memory erased prior to upgrading the IOS image from the TFTP server?

Router# copy tftp flashAddress or name of remote host []? 192.168.2.167
Source filename []? c1600-k8sy-mz.123-16a.bin
Destination filename [c1600-k8sy-mz.123-16a.bin]?
Accessing tftp://192.168.2.167/ c1600-k8sy-mz.l23-16a.bin…
Erasing flash before copying? [confirm]
Erasing the flash filesystem will remove all files! continue? [confirm]
Erasing device
Eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
Eeeeeeeeeeeeeeeeeeeeeeeeeeeeeee …erased
Erase of flash: complete

Loading c1600-k8sy-mz.l23-16a.bin from 192.168.2.167 (via Ethernet0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK – 6888962/13777920 bytes]
verifying checksum… OK (0x7BF3)
6888962 bytes copied in 209.920 secs (32961 bytes/sec)
Router#


A. The router cannot verify that the Cisco IOS image currently in flash is valid
B. Flash memory on Cisco routers can contain only a single IOS image.
C. Erasing current flash content is requested during the copy dialog.
D. In order for the router to use the new image as the default, it must be the only IOS image in flash.

 Answer: C

 Question 4

 How does using the service password encryption command on a router provide additional security?

A. by encrypting all passwords passing through the router
B. by encrypting passwords in the plain text configuration file
C. by requiring entry of encrypted passwords for access to the device
D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges
E. by automatically suggesting encrypted passwords for use in configuring the router

 Answer: B

 Question 5

 What is a global command?
A. a command that is available in every release of IOS, regardless of the version or deployment
status
B. a command that can be entered in any configuration mode
C. a command that is universal in application and supports all protocols
D. a command that is implemented in all foreign and domestic IOS versions
E. a command that is set once and affects the entire router

 Answer: E

 Question 6

 Refer to the exhibit.

 What is the effect of the configuration that is shown?

A. It configures SSH globally for all logins.
B. It tells the router or switch to try to establish an SSh connection first and if that foils to use Telnet.
C. It configures the virtual terminal lines with the password 030752180500.
D. It configures a Cisco network device to use the SSH protocol on incoming communications via
the virtual terminal ports.
E. It allows seven failed login attempts before the VTY lines are temporarily shutdown.

 Answer: D

 Question 7

 Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose
three)
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces

 Answer: A D F'

 Question 8

 Which command shows your active Telnet connections?
A. show sessions
B. show cdp neighbors
C. show users
D. show queue

 Answer: A

 Question 9

 Which command would you configure globally on a Cisco router that would allow you to view
directly connected Cisco devices?
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp

 Answer: C

 Question 10

 A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the confguration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?
A. service password-encryption
access-list 1 permit 192.168.1.0 0.0.0.255
line vty 0 4
login
password cisco
access-class 1
B. enable password secret
line vty 0
login
password cisco
C. service password-encryption
line vty 1
login
password cisco
D. service password-encryption
line vty 0 4
login
password cisco

 Answer: C

 Question 11

 What is the effect of using the service password-encryption command?

 A. Only passwords configured after the command has been entered will be encrypted.
B. Only the enable password will be encrypted.
C. Only the enable secret password will be encrypted
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.

 Answer: E  

Comments

Post a Comment

Popular posts from this blog

7 Popular Layer 2 Attacks

-
Image
A large number of common threats need to be considered when securing a network, but a frequently overlooked area is the security of the LAN. When people think about security, often they’re thinking specifically of the layers above Layer 2, but there’s no reason to limit a security plan to these upper layers.  A good security plan should account for  all  layers, from Layer 1 through Layer 7.   Here we are discussing about some of the most common Layer 2 attacks and how they operate. 1. Spanning Tree Protocol (STP) Attacks The Spanning Tree Protocol (STP) is used on LAN-switched networks. Its primary function is removing potential loops within the network. Without STP, Layer 2 LANs simply would stop functioning, because the loops created within the network would flood the switches with traffic. The optimized operation and configuration of STP ensures that the LAN remains stable and that traffic takes the most optimized path through the network.  If an att
Read more

CCNA Latest Dumps Part 3

-
Image
QUESTION 21 Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.) A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports. B. Ensure that cables A and B are straight-through cables. C. Ensure cable A is plugged into a trunk port. D. Ensure the switch has power. E. Reboot all of the devices. F. Reseat all cables. Correct Answer: BDF QUESTION 22  A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem? A. The OSPF area is not configured properly. B. The priority on R1 sho
Read more

Nine Switch Commands Every Cisco Network Engineer Needs to Know

-
Image
1. hostname Syntax:   hostname   hostname One of the most basic network commands,  hostname  configures the hostname used for a device. This hostname identifies the device to other locally connected devices for protocols such as the Cisco Discovery Protocol (CDP), which helps in the identification of devices attached directly to the network. Although it is not case-sensitive, the hostname must follow certain rules: It must begin with a letter and end in a letter or digit, and interior characters must be letters, digits, or hyphens (-). 2. ip default-gateway Syntax:   ip default-gateway  gateway The  ip default-gateway  command configures the default gateway for a switch when IP routing is  not  enabled (with the  ip routing  global configuration command), which is typical when lower-level Layer 2 switches are being configured. The easiest way to determine whether IP routing has been enabled is to run the  show ip route  command. When IP routing has not bee
Read more