CCNA Latest Dumps Part 3


QUESTION 21

Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)




A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.

Correct Answer: BDF

QUESTION 22 

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link




The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?

A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.

Correct Answer: D


QUESTION 23 

What will happen if a private IP address is assigned to a public interface connected to an ISP?

A. Addresses in a private range will be not be routed on the Internet backbone.
B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.

Correct Answer: A

QUESTION 24 

Refer to the exhibit. The Bigtime router is unable to authenticate to the Littletime router. What is the cause of the problem?


A. The usernames are incorrectly configured on the two routers.
B. The passwords do not match on the two routers.
C. CHAP authentication cannot be used on a serial interface.
D. The routers cannot be connected from interface S0/0 to interface S0/0.
E. With CHAP authentication, one router must authenticate to another router. The routers cannot be configured to authenticate to each other.

Correct Answer: B

QUESTION 25 

What will be the result if the following configuration commands are implemented on a Cisco switch?

Switch(config-if)# switchport port-security
Switch(config-if)# switchport port-security mac-address sticky

A. A dynamically learned MAC address is saved in the startup-configuration file.
B. A dynamically learned MAC address is saved in the running-configuration file.
C. A dynamically learned MAC address is saved in the VLAN database.
D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

Correct Answer: B

QUESTION 26 

Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch.

2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1

The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.)



A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1.

Correct Answer: BD

Comments

Popular posts from this blog

7 Popular Layer 2 Attacks

Nine Switch Commands Every Cisco Network Engineer Needs to Know